- 請輸入產品關鍵字：
-
公司名稱：上海斯奉電子科技有限公司
地址:上海市浦東區聽康路190弄10號1802室
郵編：200129
電話：86-021-58580866
手機: 13162402280
聯系人: 張春
傳真：86-021-50250876
E-mail: 13162402280@163.com
- 當前位置：首頁 > 產品展示 > 膠帶切割機 > 素膠紙機/膠帶切割機 > ZCUT-9膠紙機，日本速膠紙機ZCUT-9,原裝素膠紙機ZCUT-9
ZCUT-9膠紙機，日本速膠紙機ZCUT-9,原裝素膠紙機ZCUT-9的詳細資料：
ZCUT-9膠紙機，日本速膠紙機ZCUT-9,原裝素膠紙機ZCUT-9
無滾輪設計
切割zui大寬度為60mm
記憶功能 (作業前可自由設定六組不同長度需求供應用)
透過彈性膠卷輔軸可輕易固定膠卷
預設, 循環及作業計數功能
同一時間可使用兩卷膠帶
保護裝置，刀口處加有安全防護擋板
數字控制切割長度
不需因膠帶厚薄調校
內建鉗子, 潤滑油, 隔板供簡易操作
防靜電ABS材質
提高安全性，當警戒裝置運作及暫停膠紙機后，即使把堵塞物清除，膠紙機
也不會立刻運作，需重新按開始鍵后才可正常使用
ZCUT-9膠紙機-膠帶切割機
膠帶切割機剪裁長度：5 - 999 mm
膠帶切割機剪裁寬度:6 - 60 mm
膠帶切割機使用膠帶:纖絲膠帶、硬膠帶、醋酸酯、玻璃墻紙、雙面膠、諾梅克斯、封口膠、透明膠帶、工藝膠帶、遮蔽膠帶及塑料膠帶等
膠帶切割機能夠裁斷面不粘物:表面保護膜、紙膠帶、絕緣膜、鋁箔、銅箔等
選購配件明細表：
配件編號 | 配件名稱 | PARTS NAME | SPEC | FIGURE | |
100 | 外殼 | Body Cover |
|
| |
102 | 前擋板 | Knife Box Fixed Plate |
|
| |
103 | 撥動片 | Knife Box Lever |
|
| |
104 |
| Coil Spring |
|
| |
105 | 標牌 | Switch Name Plate |
|
| |
200 | 刀盒組件 （含刀片） | Knife Box Set | #201~214 Assembly（# 201 ~ 214集） |
| |
201 | 刀盒 | Knife Box |
| ||
202 | 保護罩1 | Upper Knife Safe Plate |
| ||
203 | 刀盒彈簧 | Coil Spring |
| ||
204 | 保護罩2 | Oil Sponge |
| ||
205 | 右軌道 | Knife Support Rail(LH) |
| ||
206 | 左軌道 | Knife Support Rail(RH) |
| ||
207 | 下刀片 | Bottom Knife |
| ||
208 | 刀片壓板1 | Bottom Knife Pressing Plate(R) |
| ||
209 | 刀片壓板2 | Bottom Knife Pressing Plate(L) |
| ||
210 | 彈簧 | Bottom Knife Torsion Spring |
| ||
211 | 上刀片 | Upper Knife |
| ||
207/211 | 刀片組件 |
|
|
| |
212 | 刀片彈片 | Upper Knife Fix Plate Spring |
| ||
213 | 彈片螺絲 | Cross Round Head Tapping Screw | 3X6L | ||
214 | 剪擋板 | Tape Discharge Guide Plate Set |
| ||
301 | 前端固定板1 | Knife Gear Box Front |
| ||
302 | 前端固定板2 | Knife Gear Box Rear |
| ||
303 | 感應器組件 | Tape Auto Sensor Set |
| ||
304 | 推刀板 | Lower Knife Slide Plate |
|
305 | 軸套 | Knife Cam Plate Roller |
|
| |
306 | 感應開關 | Knife Sensor Lever |
| ||
307 | 刀片控制桿 | Knife Cam Plate |
| ||
308 | 刀片控制擋板1 | Knife Cam Fix Bar LH |
| ||
309 | 刀片控制擋板2 | Knife Cam Fix Bar RH |
| ||
310 | 小齒輪 | Knife Motor Pinion |
| ||
311 | 齒輪1 | Knife 1'st Gear |
| ||
312 | 齒輪2 | Knife 2'nd Gear |
| ||
313 | 齒輪3 | Knife 3'rd Gear |
| ||
314 | 齒輪5 | Knife Main Gear |
| ||
315 | 軸套 | Knife Gear Bearing |
| ||
316 | 齒輪軸 | Knife Gear Shaft |
| ||
317 | 剪切電機 | Knife Motor |
| ||
318 | 電機電纜 | Knife Motor Cable |
| ||
319 | 變壓器支架 | Transformer Bracket |
| ||
320 | 變壓器 | Power Transformer |
| ||
321 | 接地線 | Earth Wire |
| ||
322 | 連接線 | Innet Cable Shot |
| ||
323 | 光電開關 | Knife Sensor Set |
| ||
324 | 彈簧 | Coil Spring |
| ||
325 | 彈簧 | Knife Sensor Torsion Spring |
| ||
326 | 鐵軸 | Knife Cam Plate Shaft |
| ||
327 | 剪切電機螺絲 (十字圓頭螺釘) | Cross Round Head screw | M2.6X6L | ||
328 | 十字盤頭自攻螺釘 | Cross Round Head Tapping Screw | 3X8L | ||
401 | 底板 | Bottom Case |
| ||
402 | 方底腳 | Cushion Rubber(B) |
| ||
403 | 圓底腳 | Cushion Rubber(A) |
| ||
404 | 滑動板 | Tape Wide Control Plate |
| ||
405 | 分隔板 | Tape Separating Plate |
| ||
406 | 小分隔板 | Tape Separating Sub Plate |
| ||
407 | 支撐板 | Angle Plate |
| ||
408 | 角板橡膠墊 | Angle Plate Cushion Rubber |
| ||
409-1 | 導向板 | Tape Guide Plate (LH) | 左 | ||
409-2 | 導向板 | Tape Guide Plate (RH) | 右 | ||
410 | 鑷子 | Pincette |
| ||
411 | 鐵軸 | Tape Guide Shaft |
| ||
412 | 硅油 | Oil Bottle |
| ||
413 | 十字圓頭螺釘 | Cross Round Head Screw | M3X6L | ||
414 | 基板 ( C ) | Base PCB (C) |
| ||
415 | 電源插座 | Innet - A |
| ||
416 | 電源開關 | Power Switch |
| ||
417 | 連接線 | Innet Cable Long |
| ||
418 | 電源控制板 |
|
|
| |
419 | 控制主板1 |
|
|
| |
409-1 | 左壓板 |
|
|
| |
409-2 | 右壓板 |
|
|
| |
409-3 | 左滑動板 |
|
|
| |
420 | 固定片 |
|
|
| |
422 | 電源連接線1 |
|
|
| |
423 | 電源連接線2 |
|
|
| |
424 | 電源連接線3 |
|
|
| |
500 | 出紙輪組件 | Front Frame Set | #501~517 Assembly | ||
501 | 走紙輪支架1 | Front Frame LH |
| ||
502 | 走紙輪支架2 | Front Frame RH |
| ||
503 | 出紙輪 | Middle Roller |
| ||
504 | 壓紙輪1 | Rugged Roller Lower |
| ||
505 | 壓紙輪2 | Rugged Roller Upper |
| ||
506 | 壓膠板 | Tape Guide Entrance |
| ||
507 | 滑動頭1 | Rugged Roller Bushing |
| ||
508 | 彈簧 | Rugged Roller Spring |
| ||
509 | 磁鐵 | Magnet |
| ||
510 | 壓片 | Earth Plate |
| ||
511 | 齒輪6 | Middle Roller Gear |
| ||
512 | 齒輪7 | 2'nd Idle Gear |
| ||
513 | 齒輪8 | Rugged roller Drive Gear |
| ||
514 | 齒輪9 | Lower Rugged Gear |
| ||
515 | 齒輪10 | Upper Rugged Gear |
| ||
516 | 3*12螺絲 | Cross Round Head Screw | M3X11.3L | ||
517 | 墊圈 | Stop washer |
| ||
518 | 靜電刷 | Static Brush |
| ||
601 | 左支架板 | Main Frame LH |
| ||
602 | 右支架板 | Main Frame RH |
| ||
603 | 壓膠板2 | Tape Check Plate |
| ||
604 | 壓膠板3 | Tape Regulating Plate |
| ||
605 | 進紙輪 | Large Roller |
| ||
606 | 毛刷 | Brush |
| ||
607 | 傳動輪1 | Large Pressing Roller |
| ||
608 | 傳動輪2 | Tape Support Roller A |
| ||
609 | 固定桿 | Tape Security Pole |
| ||
610 | 傳動輪3 | Tape Support Roller B |
| ||
611 | 進紙輪電機 | Geared Motor |
| ||
612 | 齒輪11 | Motor Gear |
| ||
613 | 齒輪12 | Rotating Gear |
| ||
614 | 齒輪13 | Dubble Gear |
| ||
615 | 齒輪14 | Pressing Roller Gear |
| ||
616 | 齒輪15 | 1'st Idle Gear |
| ||
617 | 壓按按片 | Guide Plate Hanger |
| ||
618 | 彈簧 | Guide Plate Hanger Spring |
| ||
619 | 鐵軸 | Tape Guide Set Pin |
| ||
620 | 滑動頭2 | Large Pressing Roller Bushing |
| ||
621 | 彈簧1 | Large Pressing Roller Torsion Sping-LH |
| ||
622 | 彈簧2 | Large Pressing Roller Torsion Sping-RH |
| ||
623 | 螺絲3*6 | Cross Flat Head Screw | M3X6L | ||
624 | 螺絲3*8 | Trus Head Tapping Screw | M4x8L | ||
625 | M3螺母 | Frange Nut | M3X3.4H | ||
626 | 4*10螺絲 | Tapping Screw | 4X12L | ||
627 | 扭簧 | Tape Guide Set Torsion Spring |
| ||
628 | 按鍵主板 | Button PCB (A) |
| ||
629 | 按制主板2 | Side Frame PCB (B) |
| ||
630 | 光電開關 | Mili Sensor |
| ||
631 | 連接線 | Button PCB Cable |
| ||
632 | E電源連接線4 | Side Frame PCB Cable |
| ||
700 | 壓線板組件 | Tape Guide Frame Set | #701~710 Assembly | ||
701 | 左線板 | Tape Guide Frame (A) |
| ||
702 | 右線板 | Tape Guide Frame (B) |
| ||
703 | 壓輪1 | Guide Roller |
| ||
704 | 壓輪2 | Braker Roller |
| ||
705 | 左滑動片 | Braker (A) |
| ||
706 | 右滑動片 | Braker (B) |
| ||
707 |
| Curving Spring |
| ||
708 | 鐵軸 | Guide Roller Shaft |
| ||
709 | 4*60螺絲 | Cross Round Head Screw | M4X60L | ||
710 | M4螺母 | Nut | M4X3.2H | ||
801 | 電源線 | Power Cord |
|
| 如果你對ZCUT-9膠紙機，日本速膠紙機ZCUT-9,原裝素膠紙機ZCUT-9感興趣，想了解更詳細的產品信息，填寫下表直接與廠家聯系： |
| 相關同類產品： |